Removal and installation of the dashboard. Nissan Almera (from 1995 to 1999 release)
Service of Nissan Almera from 1995 to 2000 in N15 body
1. General information
2. General requirements to car repairs
3. Operation and maintenance of the car
4. Petrol engines
5. Diesel engines
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
11.1. Main data
11.2. Repair of a body
11.2.1. Removal and installation of a cowl
11.2.2. Removal and installation of a front bumper
11.2.3. Removal and installation of a rear bumper
11.2.4. Removal and installation of a forward wing
11.2.5. Removal and installation of forward and back doors
11.2.6. Removal and installation of an upholstery of forward doors
11.2.7. Removal and installation of an upholstery of back doors
11.2.8. Removal and installation of window regulators of forward and back doors
11.2.9. Removal and installation of the external handle of a door
11.2.10. Removal and installation of locks of doors
11.2.11. Removal and installation of glasses
11.2.12. Removal and installation of a door of a back (a body like hatchback)
11.2.13. Removal and installation of a trunk lid (a body like sedan)
11.2.14. Removal and installation of the dashboard
11.3. System of heating and ventilation
11.4. Climatic installation (conditioner)
11.5. System of safety cushions and prednatyazhitel of seat belts
12. Appendices
13. Schemes of electric equipment
 









11-2-14-snyatie-i-ustanovka-paneli-priborov.html

11.2.14. Removal and installation of the dashboard

During the work be guided by fig. 9.34.

Fig. 9.37. Screws of fastening of the central console assembled



Fig. 9.38. Screw of fastening of the lower part of facing of a forward right rack of a body


Disconnect minus a wire from the rechargeable battery. Remove modules of safety cushions from the driver and the passenger (depending on configuration option). Take out an ashtray. Turn out the screws of fastening of the central part of facing of the panel located under the autoradio tape recorder (fig. 9.35). Remove the central part of facing of the dashboard, taking it from two spring locks located over the central nozzles of ventilation then remove switches and separate shtekerny blocks. Remove the autoradio tape recorder and the central ware box. Turn out screws of fastening of the control panel of ventilation and heating (fig. 9.36). Remove the lighter and illumination of an ashtray. Depending on a complete set, shift a gear shifting lever cover from the lower situation or remove a gear shifting lever casing. Move sitting against the stop forward, then remove fastenings of a back part of the central console (fig. 9.37).

Fig. 9.39. Screws of fastening (1) and spring latches (2) lower parts of facing of the dashboard


Fig. 9.40. Screws of fastening of the top and lower parts of a casing of facing of a shaft of steering


Fig. 9.41. Screws of fastening of the dashboard


Fig. 9.42. Fastening of the left side of the dashboard: 1 — the aligning ledge; 2 — dredging for the aligning ledge


Move sitting back and remove fastenings of a forward part of the central console. Turn out a back bolt of fastening of a forward part of the central console which is between the lever of gear shifting and the lever of the drive of the parking brake. Raise the central console for a back part, take out bolts of fastening of forward and back parts and remove the console assembled. Open a ware box, remove the lower axes of fastening and put forward a ware box. Disconnect the switch of illumination of a ware box and take out a bulb together with the boss. Remove facing of a forward right rack of a body under the dashboard (fig. 9.38). Remove on the left side the lower part of facing of the dashboard (
fig. 9.39). Separate sockets of a sound signal, remove a steering wheel. At the same time you watch that forward wheels were established in the situation corresponding to the rectilinear movement of the car. Remove a casing of facing of a shaft of steering (fig. 9.40). Remove a frame of a combination of devices. Remove a combination of devices. On the left side remove and disconnect a wire of management of external rear-view mirrors, then the proofreader of provision of headlights in the vertical plane. Turn out the screw of fastening of the dashboard located around a combination of devices then the screws which are at the basis of the central part of the dashboard and the lower screws of fastening from each party (fig. 9.41). Exempt from spring latches from each party facing of forward racks of a body. On cars with the anti-theft device remove on the right side and disconnect a control lamp. Remove decorative caps of the top screws of fastening of the panel. Turn out the top screws of fastening of the dashboard, then carefully take out two top aligning plugs and air ducts (fig. 9.42) together with the assistant, trying not to damage governing bodies.
You make installation in the sequence, the return to removal. At the same time you monitor the correct centering of the dashboard on the fixing plugs. Pay attention to the correct provision of air ducts. Connect shtekerny blocks. Before final installation it is necessary to be convinced of operability of all governing bodies.

"previous page
11.2.13. Removal and installation of a trunk lid (a body like sedan)
following page"
11.3. System of heating and ventilation







7f435ca2