Service of Nissan Almera from 1995 to 2000 in N15 body
1. General information
2. General requirements to car repairs
3. Operation and maintenance of the car
4. Petrol engines
5. Diesel engines
6. Transmission
6.1. Coupling
6.2. Mechanical transmission
6.3. Automatic transmission
6.3.1. General information
6.3.2. Adjustment of a cable of system of compulsory return gear shifting ("kick down")
6.3.3. Adjustment of a cable of the drive of the selector
6.3.4. Adjustment of the selector of the transmission
6.3.5. Removal and installation of the automatic transmission
6.4. Drive of forward wheels
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Schemes of electric equipment
 





7f435ca2


6-3-5-snyatie-i-ustanovka-avtomaticheskojj-korobki-peredach.html

6.3.5. Removal and installation of the automatic transmission


Fig. 4.46. Gear shifting mechanism details: 1 — draft of the selector of the transmission; 2 — the lever of compulsory return gear shifting; 3 — a selector cam; 4 — a lamellar spring of the reducing valve; 5 — the switch of the blocking device of a starter; 6 — a selector cable; 7 — the sector of the lever of the selector; 8 — the blocking button; 9 — the selector lever handle; 10 — a control lamp of inclusion of transfer; 11 — a spring; 12 — an arm; 13 — laying; 14 — a cable of compulsory return gear shifting; 15 — draft of the drive of position "P" of the lever of the selector


Fig. 4.52. Details of a case of the automatic transmission: 1 — connecting draft; 2 — the hydrotransformer; 3 — a hydrotransformer case; 4 — the masloizmeritelny probe; 5 — the directing tube; 6 — the regulator; 7 — a transmission case; 8 — laying; 9 — a side cover; 10 — a stopper of a masloslivny opening; 11 — the pallet; And — to the oil heater


Fig. 4.50. Placement of a stopper of a masloslivny opening of the automatic transmission


Fig. 4.51. Otvorachivaniye of bolts of fastening of the hydrotransformer to a drive plate


When working be guided by fig. 4.46 and 4.52. Remove the rechargeable battery, previously having disconnected wires. Remove the assembly block under a cowl of the engine and take him aside, without disconnecting wires. Remove an air duct. Put the car on support so that forward wheels did not concern the earth. Merge oil from the transmission (fig. 4.50). Remove wheels and an antisplash guard of the left wheel. Disconnect electric sockets, wires, the selector, a cable of compulsory return gear shifting from the transmission. Remove shaft of the drive of forward wheels (see further). Remove a starter (see section. "Electric equipment"). Disconnect from a masloprivoda box case. Remove a safety guard of the hydrotransformer and a back cover. Turn off and remove an available bolt of fastening of the hydrotransformer (fig. 4.51). Then by means of a face key and the extender turn a pulley of a bent shaft and turn off
the remained three bolts of fastening of the hydrotransformer to a drive plate as they become available. Establish a support between the central cross-piece and the engine, supporting the power unit. Establish a hydraulic jack for support of the transmission. Remove back, then left arms of a suspension bracket of the transmission. Turn off bolts of fastening of the transmission to the engine and take out it through a bottom of a motor compartment, holding at the same time the hydrotransformer.

Fig. 4.53. Check of distance between fastening of the hydrotransformer and the surface of interface of a case of the automatic transmission to the engine: X — there have to be not less than 21,1 m


At installation of the transmission replace all removed epiploons, rubber rings, laying and самоконтрящиеся nuts. Grease with a thin butter layer of an edge of new epiploons before their installation in openings of an entrance of power shafts of the transmission. Check distance between fastening of the hydrotransformer and the surface of interface of the automatic transmission to the engine (fig. 4.53).
Carry out operations on installation of the transmission as it should be, the return to removal.
After installation of the transmission fill in necessary amount of oil in its case, it is desirable warm. When filling oil the lever of the selector has to be installed in situation "N" or "P". Launch the engine. Check operation of the transmission idling of the engine and during a trial trip on the car.

"previous page
6.3.4. Adjustment of the selector of the transmission
following page"
6.4. Drive of forward wheels