Service of Nissan Almera from 1995 to 2000 in N15 body
1. General information
2. General requirements to car repairs
3. Operation and maintenance of the car
4. Petrol engines
4.1. Removal and installation of the power unit
4.2. Dismantling and assembly of the engine
4.3. Block of cylinders
4.4. Conrod and piston group
4.5. Bent shaft and flywheel
4.6. Gas distribution mechanism
4.7. Head of the block of cylinders of GA14DE and GA16DE engines
4.8. Head of the block of cylinders of the SR20DE engine
4.8.1. Removal and installation of a cover of a head of the block of cylinders
4.8.2. Removal and installation of a forward cover of the drive of the mechanism of gas distribution
4.8.3. Removal and installation of a chain of the drive of camshafts
4.8.4. Removal of a head of the block of cylinders
4.8.5. Check of technical condition and installation of a head of the block of cylinders
4.8.6. Removal, check of technical condition and installation of camshafts
4.9. Cooling system
4.10. Lubrication system
4.11. System of production of the fulfilled gases
4.12. Power supply system
4.13. Complex Control System of the Engine (CCSE)
5. Diesel engines
6. Transmission
7. Running gear
8. Steering
9. Brake system
10. Electric equipment
11. Body
12. Appendices
13. Schemes of electric equipment
 





7f435ca2


4-8-1-snyatie-i-ustanovka-kryshki-golovki-bloka-cilindrov.html

4.8.1. Removal and installation of a cover of a head of the block of cylinders


Fig. 2.36. A detachment of wires of high voltage from spark plugs




Fig. 2.37. Release of wires from fastening brackets


Fig. 2.38. Detachment of a hose of a sapun on the right side




Fig. 2.39. Detachment of a hose of a sapun on the left side


Fig. 2.40. Order of an inhaling of nuts of fastening of a cover of a head of the block of cylinders


Disconnect a wire from the "minus" plug of the rechargeable battery. Disconnect wires of high voltage from candles and exempt them from the brackets of fastening located on a cover of a head of the block of cylinders (fig. 2.36, 2.37). Remove collars of fastening and disconnect hoses of a sapun of ventilation of a case on the back party of a cover (fig. 2.38, 2.39). Weaken collars of fastening and disconnect an oil separator hose from the union located on a cover and a hose from the union in the oil separator basis. Turn out bolts of fastening and remove an oil separator from a forward part of a head of the block of cylinders. Turn out in the sequence, return specified fig. 2.40, and remove nuts of fastening of a cover of a head of the block of cylinders together with washers. Uncover.
Take laying of a cover and take out sealing rings from nests for spark plugs and the central hairpin on a cover of a head of the block of cylinders.

Fig. 2.41. Putting sealant on semicircular dredging of a head of the block of cylinders at installation of a cover of a head of the block of cylinders


Before installation carefully clear the surfaces of interface of a head of the block of cylinders and a cover, remove oil traces. Apply a sealant layer on the surface of three semicircular dredging of a head of the block of cylinders (fig. 2.41). Establish rubber laying in a fillet of a cover of a head of the block of cylinders, be convinced that it is correctly laid on all length. Establish four sealing rings in openings for wires of high voltage and a ring in an opening of the central hairpin. If necessary sealing rings can be fixed in the necessary situation with the sealant help.
Apply a layer of sealant about 1 cm wide on laying of a cover of a head of the block of cylinders at the edges of bearing cover openings on the left side of the camshaft of final valves. Carefully install a cover of a head of the block of cylinders on the engine, watching to shifting laying and sealing rings. Be convinced of the correct provision of a cover of a head of the block of cylinders, establish rubber rings, washers and nuts on hairpins.
After installation of a cover of a head of the block of cylinders slightly tighten the central nut 1 (see fig. 2.40) and four angular nuts in the following sequence: 10, 11, 13 and 8. Then tighten all other nuts of fastening the set moment. Execute further operations as it should be, the return to removal.

"previous page
4.8. Head of the block of cylinders of the SR20DE engine
following page"
4.8.2. Removal and installation of a forward cover of the drive of the mechanism of gas distribution